Microdeck.tools 100% 瀏覽器本地執行

PCB 走線寬度與載流量計算器

New

依電流、銅厚與溫升計算所需走線寬度,或計算現有走線的最大電流,並提供電阻與壓降。

100% 瀏覽器本地執行 不上傳至伺服器 即時顯示結果

這個工具替您省下寶貴時間了嗎? 歡迎自願贊助,協助 Microdeck 維持免費與穩定運作 · 最低 $3 起。

底層運作原理

IPC-2221 gives the allowed current as I = k × ΔT^0.44 × A^0.725, where A is the copper cross-section in square mils, ΔT is the temperature rise in °C and k is 0.048 for outer layers and 0.024 for inner layers. The tool inverts it to get the area for a current, then divides by copper thickness (1 oz is about 1.378 mil, or 35 µm) to get the width.

詳細操作步驟

1

Enter the current and the temperature rise you can accept.

2

Choose copper weight and whether the trace is on an external or internal layer.

3

Optionally enter the trace length to get resistance and voltage drop.

4

Read the width in mm and mil.

核心功能與效能優勢

  • Width from current, or current from width
  • External and internal layers
  • Resistance and voltage drop for a trace length
  • Millimetre and mil results

運算方法、公式與技術標準

IPC-2221 curves were fitted for currents up to about 35 A, widths up to 400 mil and rises of 10 to 100 °C. Resistance uses copper at 20 °C.

實作範例與邊界案例

3 A on an outer layer

輸入
3 A, 10 °C rise, 1 oz copper, external
輸出
about 1.37 mm wide

An inner layer needs more than twice the width.

使用限制與精準度說明

  • • IPC-2221 is conservative for external layers and less accurate for very high currents; IPC-2152 gives better data when you need it.
  • • It ignores nearby heat sources, copper pours that help cooling and vias, so check hot designs by test.

瀏覽器本地運算與隱私保障

傳統線上轉換網站會將您的文件、文字片段或影音檔案上傳至遠端伺服器。PCB 走線寬度與載流量計算器 完全在您的瀏覽器分頁內運行:

於此分頁本地處理

您的檔案與文字都在裝置本機計算,不會傳送內容至任何後端伺服器。

絕不記錄操作內容

Microdeck 不會記錄或儲存您在工具內貼上的任何檔案或程式碼。

分頁記憶體即時釋放

所有暫存結果僅存在目前分頁記憶體中,重設或關閉分頁後即刻清除。

常見問題 (FAQ)

Why are internal traces wider?

Inner copper is surrounded by laminate and cannot shed heat to air, so the same current causes a bigger temperature rise.

What temperature rise should I pick?

10 °C is a common safe choice. Higher rises save space but heat the board and nearby parts.

Does this replace a design rule check?

No. It is a quick estimate; confirm with your fab and safety standards, especially for mains voltages.

探索相關微型工具

支持 Microdeck

完全自願 · $3 起 · 免註冊帳號

選擇金額 (USD):已選金額:$5

單次最低贊助金額為 $3 USD。

完全自願 · $3 起 · 將透過 Gumroad 安全結帳頁面完成。