Microdeck.tools 100% ブラウザ完結

基板パターン幅・許容電流計算機

New

電流、銅箔厚、温度上昇から必要なパターン幅を、または既存パターンの最大電流を計算します。

100% ブラウザ完結 サーバー送信なし 即時処理

このツールは作業時間の短縮に役立ちましたか? Microdeckの無料運営と継続開発への応援(任意・$3〜)。

仕組みと内部処理

IPC-2221 gives the allowed current as I = k × ΔT^0.44 × A^0.725, where A is the copper cross-section in square mils, ΔT is the temperature rise in °C and k is 0.048 for outer layers and 0.024 for inner layers. The tool inverts it to get the area for a current, then divides by copper thickness (1 oz is about 1.378 mil, or 35 µm) to get the width.

使い方ステップ

1

Enter the current and the temperature rise you can accept.

2

Choose copper weight and whether the trace is on an external or internal layer.

3

Optionally enter the trace length to get resistance and voltage drop.

4

Read the width in mm and mil.

主な機能と特長

  • Width from current, or current from width
  • External and internal layers
  • Resistance and voltage drop for a trace length
  • Millimetre and mil results

計算ロジック・仕様・技術基準

IPC-2221 curves were fitted for currents up to about 35 A, widths up to 400 mil and rises of 10 to 100 °C. Resistance uses copper at 20 °C.

入出力の例・エッジケース

3 A on an outer layer

入力
3 A, 10 °C rise, 1 oz copper, external
出力
about 1.37 mm wide

An inner layer needs more than twice the width.

仕様上の制限・精度に関するご注意

  • • IPC-2221 is conservative for external layers and less accurate for very high currents; IPC-2152 gives better data when you need it.
  • • It ignores nearby heat sources, copper pours that help cooling and vias, so check hot designs by test.

ブラウザ内ローカル処理とプライバシー保護

一般的なWebツールは文書やメディアを外部サーバーへ送信します。基板パターン幅・許容電流計算機 はお使いのブラウザタブ内のみで完結します:

このタブ内で処理完結

入力テキストやファイルは端末内で処理され、外部の処理サーバーへアップロードされません。

入力データのログ保存なし

作業内容や貼り付けたデータを保存・記録しません(通常の静的配信CDNリクエストのみ発生します)。

タブ単位の一時メモリ管理

作業データはタブ内のメモリ上のみに保持され、リセットまたはタブを閉じると破棄されます。

よくある質問 (FAQ)

Why are internal traces wider?

Inner copper is surrounded by laminate and cannot shed heat to air, so the same current causes a bigger temperature rise.

What temperature rise should I pick?

10 °C is a common safe choice. Higher rises save space but heat the board and nearby parts.

Does this replace a design rule check?

No. It is a quick estimate; confirm with your fab and safety standards, especially for mains voltages.

関連するマイクロツール

Microdeckを応援する

完全任意 · $3から · アカウント登録不要

金額を選択 (USD):選択中:$5

最小金額は $3 USD です。

完全任意 · $3から · Gumroadの安全な決済ページが開きます。