Microdeck.tools 100% 브라우저 실행

PCB 트레이스 폭·전류 용량 계산기

New

전류, 구리 두께, 온도 상승으로 필요한 트레이스 폭을, 또는 기존 트레이스의 최대 전류를 계산합니다.

100% 브라우저 실행 서버 업로드 없음 즉시 결과 확인

이 도구가 시간을 절약하는 데 도움이 되었나요? Microdeck을 무료로 유지하고 개선하는 데 힘을 보태주세요. 자율 참여 · $3부터.

작동 원리 및 구조

IPC-2221 gives the allowed current as I = k × ΔT^0.44 × A^0.725, where A is the copper cross-section in square mils, ΔT is the temperature rise in °C and k is 0.048 for outer layers and 0.024 for inner layers. The tool inverts it to get the area for a current, then divides by copper thickness (1 oz is about 1.378 mil, or 35 µm) to get the width.

단계별 사용 방법

1

Enter the current and the temperature rise you can accept.

2

Choose copper weight and whether the trace is on an external or internal layer.

3

Optionally enter the trace length to get resistance and voltage drop.

4

Read the width in mm and mil.

주요 기능 및 장점

  • Width from current, or current from width
  • External and internal layers
  • Resistance and voltage drop for a trace length
  • Millimetre and mil results

계산 방식, 공식 및 기술 표준

IPC-2221 curves were fitted for currents up to about 35 A, widths up to 400 mil and rises of 10 to 100 °C. Resistance uses copper at 20 °C.

입출력 예시 및 엣지 케이스

3 A on an outer layer

입력
3 A, 10 °C rise, 1 oz copper, external
출력
about 1.37 mm wide

An inner layer needs more than twice the width.

제한 사항 및 정확도 안내

  • • IPC-2221 is conservative for external layers and less accurate for very high currents; IPC-2152 gives better data when you need it.
  • • It ignores nearby heat sources, copper pours that help cooling and vias, so check hot designs by test.

브라우저 로컬 처리 및 개인정보 보호

일반 웹 변환기는 문서나 미디어 파일을 원격 서버에 업로드합니다. PCB 트레이스 폭·전류 용량 계산기 도구는 현재 브라우저 탭 내부에서만 실행됩니다:

현재 탭에서 직접 처리

입력 텍스트와 파일은 외부 서버로 전송되지 않고 기기 내에서 로컬로 계산됩니다.

입력 데이터 로그 미보관

도구에 붙여넣은 파일이나 데이터를 서버에 기록하거나 저장하지 않습니다.

일시적 탭 메모리 수명주기

작업 결과는 브라우저 탭 메모리에만 유지되며 탭을 닫거나 초기화하면 즉시 해제됩니다.

자주 묻는 질문 (FAQ)

Why are internal traces wider?

Inner copper is surrounded by laminate and cannot shed heat to air, so the same current causes a bigger temperature rise.

What temperature rise should I pick?

10 °C is a common safe choice. Higher rises save space but heat the board and nearby parts.

Does this replace a design rule check?

No. It is a quick estimate; confirm with your fab and safety standards, especially for mains voltages.

관련 마이크로 도구 살펴보기

Microdeck 후원하기

100% 자율 후원 · $3부터 · 회원가입 불필요

금액 선택 (USD):선택 금액:$5

최소 후원 금액은 $3 USD입니다.

100% 자율 · $3부터 · Gumroad 안전 결제 창이 열립니다.