Microdeck.tools 100 % dans le navigateur

Calculateur de résistance LED série et parallèle

New

Calculez la résistance, la valeur E24 la plus proche, sa puissance et le courant réel à partir de la tension d’alimentation, de la tension directe et du courant.

100 % dans le navigateur Aucun envoi serveur Résultats instantanés

Cet outil vous a-t-il fait gagner du temps ? Aidez Microdeck à rester gratuit et maintenu. Facultatif · Dès $3.

Fonctionnement technique

The resistor drops whatever voltage the LEDs do not use: R = (supply − number of LEDs in series × forward voltage) ÷ current. For a parallel bank with one resistor per LED each branch is calculated separately. With one shared resistor the currents add, so the resistor carries the total and the LEDs share it unevenly, which is why the tool flags that layout.

Mode d’emploi étape par étape

1

Choose the layout: one LED or a series string, parallel with one resistor per LED, or parallel sharing one resistor.

2

Enter the supply voltage, the LED forward voltage from its datasheet and the target current.

3

Enter how many LEDs you are driving.

4

Read the exact resistance, the next standard E24 value, the resistor power and the real current with that standard part.

Fonctionnalités & performances

  • Three layouts in one tool
  • Rounds up to the next E24 value so the LED never exceeds the target current
  • Resistor power with a safe rating suggestion
  • Warns when the supply is too low for the LEDs in series

Méthodologie, formules & standards

Ohm law on the leftover voltage. The standard value is the smallest E24 value at or above the exact result, so real current is slightly lower than the target.

Exemples concrets & cas limites

Three LEDs in series

Entrée
12 V supply, 3.2 V forward, 20 mA, 3 LEDs in series
Sortie
120 Ω, 0.048 W

12 − 3 × 3.2 = 2.4 V across the resistor; 2.4 ÷ 0.02 = 120 Ω.

Four parallel LEDs, one resistor each

Entrée
9 V, 3.2 V, 20 mA
Sortie
290 Ω exact, 300 Ω E24 per LED

Limites & notes de précision

  • • Forward voltage varies with colour, current and temperature, so use the datasheet value and verify with a meter.
  • • Sharing one resistor between parallel LEDs is not recommended; small differences in forward voltage make the currents unequal.

Traitement local dans le navigateur & confidentialité

Les convertisseurs classiques envoient vos documents, extraits ou médias sur des serveurs distants. Calculateur de résistance LED série et parallèle s’exécute directement dans votre onglet :

Traité dans cet onglet

Vos textes et fichiers sont traités localement sans aucun envoi vers un serveur de calcul.

Aucune journalisation des données

Microdeck n’enregistre ni ne stocke les fichiers ou données collés dans les outils.

Mémoire éphémère de l’onglet

Les résultats restent dans la mémoire de votre onglet et sont libérés dès que vous le fermez.

Questions fréquentes (FAQ)

Why not use a resistor slightly below the calculated value?

A smaller resistor passes more current. Rounding up to the next E24 value keeps the LED at or below the target current.

What if my supply is lower than the total forward voltage?

The LEDs will not reach full brightness. Use fewer LEDs in series or a higher supply, or split them into parallel branches.

Is anything uploaded?

No. The calculation happens in your browser.

Outils associés à découvrir

Soutenir Microdeck

Entièrement facultatif · Dès $3 · Sans compte

Choisir un montant (USD) :Sélectionné :$5

Le montant minimum est de $3 USD.

100 % facultatif · Dès $3 · Paiement sécurisé via Gumroad.