Microdeck.tools 100 % en el navegador

Calculadora de resistencia para LED en serie y paralelo

New

Calcule la resistencia, el valor E24 más cercano, su potencia y la corriente real a partir de la tensión de alimentación, la tensión directa y la corriente.

100 % en tu navegador Sin subir archivos Resultados al instante

¿Te ahorró tiempo esta herramienta? Ayuda a mantener Microdeck gratis y al día. Opcional · Desde $3.

Cómo funciona por dentro

The resistor drops whatever voltage the LEDs do not use: R = (supply − number of LEDs in series × forward voltage) ÷ current. For a parallel bank with one resistor per LED each branch is calculated separately. With one shared resistor the currents add, so the resistor carries the total and the LEDs share it unevenly, which is why the tool flags that layout.

Instrucciones paso a paso

1

Choose the layout: one LED or a series string, parallel with one resistor per LED, or parallel sharing one resistor.

2

Enter the supply voltage, the LED forward voltage from its datasheet and the target current.

3

Enter how many LEDs you are driving.

4

Read the exact resistance, the next standard E24 value, the resistor power and the real current with that standard part.

Funciones principales y ventajas

  • Three layouts in one tool
  • Rounds up to the next E24 value so the LED never exceeds the target current
  • Resistor power with a safe rating suggestion
  • Warns when the supply is too low for the LEDs in series

Metodología, fórmulas y estándares técnicos

Ohm law on the leftover voltage. The standard value is the smallest E24 value at or above the exact result, so real current is slightly lower than the target.

Ejemplos prácticos y casos límite

Three LEDs in series

Entrada
12 V supply, 3.2 V forward, 20 mA, 3 LEDs in series
Salida
120 Ω, 0.048 W

12 − 3 × 3.2 = 2.4 V across the resistor; 2.4 ÷ 0.02 = 120 Ω.

Four parallel LEDs, one resistor each

Entrada
9 V, 3.2 V, 20 mA
Salida
290 Ω exact, 300 Ω E24 per LED

Límites y notas de precisión

  • • Forward voltage varies with colour, current and temperature, so use the datasheet value and verify with a meter.
  • • Sharing one resistor between parallel LEDs is not recommended; small differences in forward voltage make the currents unequal.

Procesamiento local en tu navegador y privacidad

Los conversores tradicionales suben tus documentos, textos o archivos multimedia a servidores remotos. Calculadora de resistencia para LED en serie y paralelo se ejecuta dentro de tu pestaña:

Procesado en esta pestaña

Tus textos y archivos se procesan localmente sin enviarse a ningún servidor externo.

Sin registro de tus archivos

Microdeck no guarda ni registra el contenido que introduces en las herramientas.

Memoria temporal de la pestaña

Los resultados permanecen en la memoria de tu navegador y se liberan al cerrar o reiniciar.

Preguntas frecuentes (FAQ)

Why not use a resistor slightly below the calculated value?

A smaller resistor passes more current. Rounding up to the next E24 value keeps the LED at or below the target current.

What if my supply is lower than the total forward voltage?

The LEDs will not reach full brightness. Use fewer LEDs in series or a higher supply, or split them into parallel branches.

Is anything uploaded?

No. The calculation happens in your browser.

Explora herramientas relacionadas

Apoyar a Microdeck

Totalmente opcional · Desde $3 · Sin cuenta

Elige un importe (USD):Seleccionado:$5

El aporte mínimo es de $3 USD.

Totalmente opcional · Desde $3 · Pago seguro en Gumroad.