Microdeck.tools 100% 브라우저 실행

전선 굵기(AWG)·전압 강하 계산기

New

허용 강하를 만족하는 가장 작은 AWG를 찾거나 강하, 저항, 손실 전력을 계산합니다. 구리와 알루미늄 지원.

100% 브라우저 실행 서버 업로드 없음 즉시 결과 확인

이 도구가 시간을 절약하는 데 도움이 되었나요? Microdeck을 무료로 유지하고 개선하는 데 힘을 보태주세요. 자율 참여 · $3부터.

작동 원리 및 구조

AWG diameter follows d = 0.127 mm × 92^((36 − n) ÷ 39), and area is π × d² ÷ 4. Wire resistance is ρ × length ÷ area, with ρ = 0.017241 Ω·mm²/m for copper and 0.02824 for aluminium at 20 °C. Because current flows out and back, the tool uses twice the one-way length. Drop = I × R, and the tool picks the smallest standard gauge whose drop is within your limit.

단계별 사용 방법

1

Choose whether to size a wire or to check a chosen gauge.

2

Enter current, one-way length and supply voltage.

3

Enter the maximum acceptable drop in percent, or pick the AWG to test.

4

Read the gauge, area, drop in volts and percent and the power lost in the wire.

주요 기능 및 장점

  • Standard sizes from 4/0 to AWG 40
  • Copper and aluminium
  • Results in AWG and mm²
  • Round-trip length handled automatically

입출력 예시 및 엣지 케이스

Sizing

입력
20 A, 10 m one way, 12 V, 3% drop
출력
AWG 4 (21.2 mm²)

0.36 V over a 20 m round trip needs about 19.2 mm².

Reference

입력
AWG 12
출력
2.053 mm diameter, 3.309 mm²

제한 사항 및 정확도 안내

  • • This is a voltage-drop result, not an ampacity or code rating. Insulation, bundling and ambient temperature limit safe current; follow your local electrical code.
  • • Resistance rises about 0.4% per °C above 20 °C, so hot runs drop more.

브라우저 로컬 처리 및 개인정보 보호

일반 웹 변환기는 문서나 미디어 파일을 원격 서버에 업로드합니다. 전선 굵기(AWG)·전압 강하 계산기 도구는 현재 브라우저 탭 내부에서만 실행됩니다:

현재 탭에서 직접 처리

입력 텍스트와 파일은 외부 서버로 전송되지 않고 기기 내에서 로컬로 계산됩니다.

입력 데이터 로그 미보관

도구에 붙여넣은 파일이나 데이터를 서버에 기록하거나 저장하지 않습니다.

일시적 탭 메모리 수명주기

작업 결과는 브라우저 탭 메모리에만 유지되며 탭을 닫거나 초기화하면 즉시 해제됩니다.

자주 묻는 질문 (FAQ)

Why does 12 V need such thick wire?

The same percentage drop is a much smaller voltage at 12 V, so low-voltage runs need larger conductors than mains circuits.

Is a lower AWG number a thicker wire?

Yes. AWG 10 is thicker than AWG 14. Sizes above 1 go to 1/0, 2/0, 3/0 and 4/0.

Can I use this for AC?

For short low-frequency runs it is a good estimate. Long AC runs also depend on reactance and power factor.

관련 마이크로 도구 살펴보기

Microdeck 후원하기

100% 자율 후원 · $3부터 · 회원가입 불필요

금액 선택 (USD):선택 금액:$5

최소 후원 금액은 $3 USD입니다.

100% 자율 · $3부터 · Gumroad 안전 결제 창이 열립니다.