Microdeck.tools 100 % dans le navigateur

Section de fil (AWG) et chute de tension

New

Trouvez le plus petit AWG respectant votre chute maximale, ou calculez chute, résistance et pertes. Cuivre et aluminium.

100 % dans le navigateur Aucun envoi serveur Résultats instantanés

Cet outil vous a-t-il fait gagner du temps ? Aidez Microdeck à rester gratuit et maintenu. Facultatif · Dès $3.

Fonctionnement technique

AWG diameter follows d = 0.127 mm × 92^((36 − n) ÷ 39), and area is π × d² ÷ 4. Wire resistance is ρ × length ÷ area, with ρ = 0.017241 Ω·mm²/m for copper and 0.02824 for aluminium at 20 °C. Because current flows out and back, the tool uses twice the one-way length. Drop = I × R, and the tool picks the smallest standard gauge whose drop is within your limit.

Mode d’emploi étape par étape

1

Choose whether to size a wire or to check a chosen gauge.

2

Enter current, one-way length and supply voltage.

3

Enter the maximum acceptable drop in percent, or pick the AWG to test.

4

Read the gauge, area, drop in volts and percent and the power lost in the wire.

Fonctionnalités & performances

  • Standard sizes from 4/0 to AWG 40
  • Copper and aluminium
  • Results in AWG and mm²
  • Round-trip length handled automatically

Exemples concrets & cas limites

Sizing

Entrée
20 A, 10 m one way, 12 V, 3% drop
Sortie
AWG 4 (21.2 mm²)

0.36 V over a 20 m round trip needs about 19.2 mm².

Reference

Entrée
AWG 12
Sortie
2.053 mm diameter, 3.309 mm²

Limites & notes de précision

  • • This is a voltage-drop result, not an ampacity or code rating. Insulation, bundling and ambient temperature limit safe current; follow your local electrical code.
  • • Resistance rises about 0.4% per °C above 20 °C, so hot runs drop more.

Traitement local dans le navigateur & confidentialité

Les convertisseurs classiques envoient vos documents, extraits ou médias sur des serveurs distants. Section de fil (AWG) et chute de tension s’exécute directement dans votre onglet :

Traité dans cet onglet

Vos textes et fichiers sont traités localement sans aucun envoi vers un serveur de calcul.

Aucune journalisation des données

Microdeck n’enregistre ni ne stocke les fichiers ou données collés dans les outils.

Mémoire éphémère de l’onglet

Les résultats restent dans la mémoire de votre onglet et sont libérés dès que vous le fermez.

Questions fréquentes (FAQ)

Why does 12 V need such thick wire?

The same percentage drop is a much smaller voltage at 12 V, so low-voltage runs need larger conductors than mains circuits.

Is a lower AWG number a thicker wire?

Yes. AWG 10 is thicker than AWG 14. Sizes above 1 go to 1/0, 2/0, 3/0 and 4/0.

Can I use this for AC?

For short low-frequency runs it is a good estimate. Long AC runs also depend on reactance and power factor.

Outils associés à découvrir

Soutenir Microdeck

Entièrement facultatif · Dès $3 · Sans compte

Choisir un montant (USD) :Sélectionné :$5

Le montant minimum est de $3 USD.

100 % facultatif · Dès $3 · Paiement sécurisé via Gumroad.