Microdeck.tools 100% 瀏覽器本地執行

分壓器計算器

New

計算電阻分壓器的 Vout,求目標電壓的 R2,並檢查負載造成的變化。

100% 瀏覽器本地執行 不上傳至伺服器 即時顯示結果

這個工具替您省下寶貴時間了嗎? 歡迎自願贊助,協助 Microdeck 維持免費與穩定運作 · 最低 $3 起。

底層運作原理

An unloaded divider gives Vout = Vin × R2 ÷ (R1 + R2). A load in parallel with R2 lowers the bottom resistance to R2 ∥ Rload, so the real output is lower. To hit a target, the tool solves R2 = R1 × Vout ÷ (Vin − Vout) and shows the nearest E24 part.

詳細操作步驟

1

Choose whether to find the output voltage or the R2 for a target.

2

Enter Vin and R1 (4.7k, 10k and similar are accepted).

3

Enter R2 or the target voltage, and optionally a load resistance.

4

Read Vout, ratio, current, power and the loaded result.

核心功能與效能優勢

  • Both directions in one tool
  • Load resistance shows the voltage drop caused by the load
  • Nearest E24 value for the target mode
  • Power in each resistor

實作範例與邊界案例

12 V divider

輸入
Vin 12 V, R1 10 kΩ, R2 4.7 kΩ
輸出
3.837 V unloaded

12 × 4.7 ÷ 14.7.

Hit 3.3 V

輸入
Vin 12 V, R1 10 kΩ, target 3.3 V
輸出
R2 = 3.79 kΩ, nearest E24 3.9 kΩ

使用限制與精準度說明

  • • A divider is a poor power supply: any real load pulls the output down. Use a regulator for loads above a few milliamps.
  • • Resistor tolerance (1% to 5%) shifts the output by a similar amount.

瀏覽器本地運算與隱私保障

傳統線上轉換網站會將您的文件、文字片段或影音檔案上傳至遠端伺服器。分壓器計算器 完全在您的瀏覽器分頁內運行:

於此分頁本地處理

您的檔案與文字都在裝置本機計算,不會傳送內容至任何後端伺服器。

絕不記錄操作內容

Microdeck 不會記錄或儲存您在工具內貼上的任何檔案或程式碼。

分頁記憶體即時釋放

所有暫存結果僅存在目前分頁記憶體中,重設或關閉分頁後即刻清除。

常見問題 (FAQ)

Can I power a microcontroller from a divider?

Only for a signal input with almost no current. For power, use a regulator, because the divider voltage changes with load.

How do I reduce loading error?

Make R1 and R2 at least 10 times smaller than the load resistance, at the cost of more standing current.

Is the data private?

Yes, everything runs locally.

探索相關微型工具

支持 Microdeck

完全自願 · $3 起 · 免註冊帳號

選擇金額 (USD):已選金額:$5

單次最低贊助金額為 $3 USD。

完全自願 · $3 起 · 將透過 Gumroad 安全結帳頁面完成。