Microdeck.tools 100% ブラウザ完結

分圧回路計算機

New

抵抗分圧のVoutを計算し、目標電圧に必要なR2を求め、負荷による変化も確認できます。

100% ブラウザ完結 サーバー送信なし 即時処理

このツールは作業時間の短縮に役立ちましたか? Microdeckの無料運営と継続開発への応援(任意・$3〜)。

仕組みと内部処理

An unloaded divider gives Vout = Vin × R2 ÷ (R1 + R2). A load in parallel with R2 lowers the bottom resistance to R2 ∥ Rload, so the real output is lower. To hit a target, the tool solves R2 = R1 × Vout ÷ (Vin − Vout) and shows the nearest E24 part.

使い方ステップ

1

Choose whether to find the output voltage or the R2 for a target.

2

Enter Vin and R1 (4.7k, 10k and similar are accepted).

3

Enter R2 or the target voltage, and optionally a load resistance.

4

Read Vout, ratio, current, power and the loaded result.

主な機能と特長

  • Both directions in one tool
  • Load resistance shows the voltage drop caused by the load
  • Nearest E24 value for the target mode
  • Power in each resistor

入出力の例・エッジケース

12 V divider

入力
Vin 12 V, R1 10 kΩ, R2 4.7 kΩ
出力
3.837 V unloaded

12 × 4.7 ÷ 14.7.

Hit 3.3 V

入力
Vin 12 V, R1 10 kΩ, target 3.3 V
出力
R2 = 3.79 kΩ, nearest E24 3.9 kΩ

仕様上の制限・精度に関するご注意

  • • A divider is a poor power supply: any real load pulls the output down. Use a regulator for loads above a few milliamps.
  • • Resistor tolerance (1% to 5%) shifts the output by a similar amount.

ブラウザ内ローカル処理とプライバシー保護

一般的なWebツールは文書やメディアを外部サーバーへ送信します。分圧回路計算機 はお使いのブラウザタブ内のみで完結します:

このタブ内で処理完結

入力テキストやファイルは端末内で処理され、外部の処理サーバーへアップロードされません。

入力データのログ保存なし

作業内容や貼り付けたデータを保存・記録しません(通常の静的配信CDNリクエストのみ発生します)。

タブ単位の一時メモリ管理

作業データはタブ内のメモリ上のみに保持され、リセットまたはタブを閉じると破棄されます。

よくある質問 (FAQ)

Can I power a microcontroller from a divider?

Only for a signal input with almost no current. For power, use a regulator, because the divider voltage changes with load.

How do I reduce loading error?

Make R1 and R2 at least 10 times smaller than the load resistance, at the cost of more standing current.

Is the data private?

Yes, everything runs locally.

関連するマイクロツール

Microdeckを応援する

完全任意 · $3から · アカウント登録不要

金額を選択 (USD):選択中:$5

最小金額は $3 USD です。

完全任意 · $3から · Gumroadの安全な決済ページが開きます。