Microdeck.tools 100% di Browser

Kalkulator Pembagi Tegangan

New

Hitung Vout pembagi tegangan resistor, cari R2 untuk target, dan periksa pengaruh beban.

100% di Browser Tanpa Upload Server Hasil Instan

Apakah alat ini menghemat waktu Anda? Bantu jaga Microdeck tetap gratis dan terawat. Sepenuhnya sukarela · Mulai $3.

Cara Kerja di Balik Layar

An unloaded divider gives Vout = Vin × R2 ÷ (R1 + R2). A load in parallel with R2 lowers the bottom resistance to R2 ∥ Rload, so the real output is lower. To hit a target, the tool solves R2 = R1 × Vout ÷ (Vin − Vout) and shows the nearest E24 part.

Panduan Langkah demi Langkah

1

Choose whether to find the output voltage or the R2 for a target.

2

Enter Vin and R1 (4.7k, 10k and similar are accepted).

3

Enter R2 or the target voltage, and optionally a load resistance.

4

Read Vout, ratio, current, power and the loaded result.

Fitur Utama & Performa

  • Both directions in one tool
  • Load resistance shows the voltage drop caused by the load
  • Nearest E24 value for the target mode
  • Power in each resistor

Contoh Kasus & Uji Coba

12 V divider

Input
Vin 12 V, R1 10 kΩ, R2 4.7 kΩ
Output
3.837 V unloaded

12 × 4.7 ÷ 14.7.

Hit 3.3 V

Input
Vin 12 V, R1 10 kΩ, target 3.3 V
Output
R2 = 3.79 kΩ, nearest E24 3.9 kΩ

Catatan Batasan & Akurasi

  • • A divider is a poor power supply: any real load pulls the output down. Use a regulator for loads above a few milliamps.
  • • Resistor tolerance (1% to 5%) shifts the output by a similar amount.

Pemrosesan Lokal di Browser & Privasi

Konverter web konvensional mengunggah dokumen, teks, atau media ke server jarak jauh. Kalkulator Pembagi Tegangan berjalan langsung di tab browser Anda:

Diproses di Tab Ini

Teks dan file Anda diproses secara lokal tanpa mengirim muatan apa pun ke server.

Tanpa Pencatatan Input

Microdeck tidak mencatat atau menyimpan file dan teks yang Anda masukkan ke ruang kerja alat.

Memori Tab Sementara

Hasil kerja hanya tersimpan di memori tab dan langsung terhapus saat Anda me-reset atau menutup tab.

Pertanyaan yang Sering Diajukan (FAQ)

Can I power a microcontroller from a divider?

Only for a signal input with almost no current. For power, use a regulator, because the divider voltage changes with load.

How do I reduce loading error?

Make R1 and R2 at least 10 times smaller than the load resistance, at the cost of more standing current.

Is the data private?

Yes, everything runs locally.

Jelajahi Alat Mikro Terkait

Dukung Microdeck

Sepenuhnya sukarela · Mulai $3 · Tanpa akun

Pilih jumlah (USD):Dipilih:$5

Jumlah dukungan minimum adalah $3 USD.

Sepenuhnya sukarela · Mulai $3 · Pembayaran aman melalui Gumroad.